Of all the different wearable items that can be embroidered, jackets would appear to be the easiest. When most of think about jackets with regards to embroidery, large areas for full backside and left chest designs come to mind. What a lot of us often forget will be the little curveballs apparel suppliers are adding into their designs such as container pleats and seams down the back. Fashion forward styles may have things like raglan sleeves that may throw off design placement given that they lack the guideline longmire coat of a shoulder seam.

One sure way to start out with a jacket that is fit for embroidery would be to focus on working with styles that give the fewest headaches. As a result, do some research on the most recent trends. In addition, start with a machine that is in top notch condition, with clean needles and bobbins. Here are the other basic elements to take into account in your search for trouble-free jacket embroidery.

Choosing a hoop

The best option in hoops for jackets is the double-substantial hoop. This hoop is taller compared to the average hoop so offers even more holding power. You can wrap your hoop with bright floral tape, medical related gauze, twill tape or bias tape to avoid hoop marks and help provide a snug fit. Tissue document, backing or waxed paper can also be used. Hoop these materials on top of the jacket, subsequently cut a screen for the embroidery. A skinny layer of foam beneath the tape may also help. But keep away from masking tape as it tends to be sticky and leaves a residue on jacket and hoop. Whenever choosing your hoops, remember that oval hoops hold better completely around than carry out square hoops with oval corners. The “square oval” retains better in the corners than on the sides, major and bottom.


The size and type of needle will depend on the fabric of the coat. Leather jackets call for an 80/12 razor-sharp. (Wedge shaped “leather” needles tend to do more harm than good.) Use this same sharp needle on poplin and other cotton-type jackets. Use a 70/10 or 80/12 light-weight ballpoint on nylon windbreakers and a 75/11 fine ballpoint on satins and oxford nylons to avoid runs in the fabric. Large wool jackets, canvas and denim jackets require a stronger razor-sharp needle. Corduroy stitches nicely with either ballpoint or razor-sharp. Understand that ballpoint needles nudge the material out of the way to be able to place the stitch, while sharps lower through the fabric. A good rule of thumb is by using the same dimensions needle to embroider as you’ll to sew the seams of the coat in assembly.

As for thread, polyester is a superb selection for embroidery on jackets that will be exposed to the elements and coastal climates. Be sure you include washing and dry cleaning up instructions together with your finished product. Consider choosing a large-eye needle when working with metallic and other heavy specialty threads

Placing the design

Hold a straight-edge across the jacket back from side seam to side seam at the bottom of the sleeves. Tag a horizontal straight line, then check this with a measurement from underneath of the jacket to the same line. Jackets are not always sewn together straight. Gauge the straight line and divide in two to get the center of the coat. Place a vertical line through the horizontal line at this time. The intersection of both lines will be the center. Should you be rotating the look to sew upside-down or sideways, take this under consideration when measuring and soon after when hooping. Use tailor’s chalk, disappearing ink pens or soap to tag your garments. Avoid using pins. Masking tape is available in slim strips at graphic and fine art stores. You can easily remove and leaves no marks. Wider masking tape, though, can leave residue.

Centering the design eight inches down from the trunk of the collar is a wonderful place to start, and really should work with most jackets. Small sizes can do better at six inches; very large ones may end up at 10 inches. The most notable of the design should fall about 2 � inches lower from the collar of the coat. But remember that this can change if the jacket has a hood. Then it will be necessary to place the look below the hood.

The easiest way to determine the center point of the design would be to have someone try the coat on, or invest in a mannequin. Pin an overview of the design or perhaps a sew-out to the back, making certain to include lettering and graphics to determine size and placement. Left or right chest models should be centered 3 to 4 inches from the edge of the jacket and 6 to 8 down from where the collar and the jacket body system intersect. When embroidering on jackets with snaps or buttons, use the second snap or key as a guide.